Coats 6200HS Truck Wheel Balancer Bedienungsanleitung

Truck Wheel BalancerModel 6200HSOPERATION GUIDEFORM 8184342

4Coats Model 6200HSFUNCTIONAL DESCRIPTIONThe following diagram shows a view from the front of thecomplete assembled Truck Wheel Balancer.1. Input Pane

Operation Guide524a4b3a 3b56671Balancer DisplayThe display combines solid-state electronics andgraphical design to provide powerful visual presentatio

6Coats Model 6200HSInput PanelThe input panel combines controls and indicators,positioned for convenience, with graphical symbolsclearly defining each

Operation Guide76. Rim Width Knob.Turn the Rim Width Knob to set rim width as measuredwith the callipers. Read the selection in the DisplayWindow.7. O

8Coats Model 6200HSAccessory Storage (1)The accessories can be stored on the protective shelvingat the back of the machine or on the moulded top tray.

Operation Guide9BALANCING OPERATIONOperation of your Coats Truck Balancer is based onLED indicators on the control panel, two soft-touchbuttons and th

10Coats Model 6200HS4. Set the Rim Width Knob as measured with theCalliper.Note: If the tire is too wide to accept the callipers,then measure over the

Operation Guide117. Attach the Weight.a. Starting with either side of the wheel, rotate thewheel in the direction of the lit arrow until all 6Arrow In

12Coats Model 6200HSBalancing Errors.The crank handle has a one-way clutch for operatorsafety, which also ensures that the wheel is spun inthe correct

Operation Guide13WEIGHT MODESThe COATS balancer features one Normal (clip-on) andfour Custom (Alu/Mag) Modes for combinations of clip-on and stick-on

14Coats Model 6200HSStatic Balancing: For this method, only LED 3 lightsto indicate a single clip-on or stick-on weight. The weightcan be positioned o

Operation Guide15SPECIAL APPLICATIONSOccasionally it may be necessary to use weightlocations which are different than those catered for inthe standard

16Coats Model 6200HS5. Spin the Wheel.Complete normal balance routine.6. Attach the Weight.Starting with either weight location, rotate the wheeluntil

Operation Guide17WHEEL MOUNTINGCareful wheel mounting is essential, as the wheel isbalanced relative to how it is mounted on the balancer.If the wheel

18Coats Model 6200HSCombination / Bolt Plate AdaptersStud piloted wheels must be mounted using thecombination adapter or a bolt plate adapter. Stud pi

Operation Guide19WHEEL MOUNTING METHODS(AUTOMOBILE WHEELS)Back Cone MountingBack cone mounting is the most common way to mountautomobile wheels. Choo

20Coats Model 6200HSBack Cone Mounting without PressureDrumEnsure the handle does not contact the cone, or thewheel will not be centered and mounted s

Operation Guide21Front Cone Mounting with an ExtensionAdaptorThe extension adaptor may be required for some lighttruck wheels and reverse-offset wheel

22Coats Model 6200HSWheel Mounting ErrorsRegardless of the mounting method used, the wheelmust be centered before balancing. A wheel should bemounted

Operation Guide23POWER SOURCESThe balancer may be powered in three different ways.1. Power Converter/Charger.The normal power method is to use the pow

Operation GuideiCONTENTSSafety Cautions and Warnings ...iiInstallation ... i

24Coats Model 6200HSAUTOMATIC CALIBRATIONThe Coats Truck Balancer is calibrated by computerbefore shipment and should not require recalibration innorm

Operation Guide254. Spin the Wheel at Least Four Times.Spin the wheel up to the normal balancing speed.After the measuring cycle, a beep will sound an

26Coats Model 6200HSSERVICE AND MAINTENANCEThe Truck Wheel Balancer can be maintained with afew simple actions performed at regular intervals.Wheel mo

Operation Guide27and shows 0 - 10 grams (0 - 0.25 ounces) for theside without the weight. If the readings are not withinthese limits, verify that the

28Coats Model 6200HSTROUBLESHOOTING GUIDEThe following tips will help to identify and correct problemswhich may be encountered when using the Truck wh

Operation Guide29F. Spinning wheel by hand - ‘EEE’ is reported.The wheel may have been spun in the wrong direction(anti-clockwise when facing the oute

30Coats Model 6200HS

Operation Guide31TECHNICAL SPECIFICATIONSRim diameter range: 330-660mm (13-26")Rim width range: 101-457mm (4-18")Rim offset range: 76-297m

32Coats Model 6200HSThe information and specifications in thismanual are based on the latest informationavailable at the time of publication. The prod

iiCoats Model 6200HSSAFETY CAUTIONS AND WARNINGS1. Read the Operators Manual before operating thebalancer for the first time. Follow all instructionsa

is a registered trademark of Hennessey Coats IndustriesForm 8184342...5840-3...10/15/10...copyright 2002...wdc Printed in the USAUSAHENNESSY IN

Operation GuideiiiINSTALLATIONYour Model 6200HS Truck Balancer and accessorieswill be delivered in a single carton mounted on a pallet.UnpackingA. Unp

ivCoats Model 6200HSSetupThe balancer is programmed before leaving the factoryto display weight imbalance in grams. To change thissetting to ounce uni

Operation Guide1INTRODUCTIONThe Coats Truck Balancer combines advanced, high-performance technology, robustness, reliability andsimplicity of operatio

2Coats Model 6200HSFEATURESThe COATS computerized wheel balancer combinesstate-of-the-art electronic accuracy with ease of use andsimplicity of design

Operation Guide3ACCESSORIESStandard AdaptorsStandard Wing Nut (P/N 8112103)40 x 4 ShaftCone ( 3.25"-5.25") (P/N 8112101)Lt Truck Cone Kit