1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 www.ammcoats.com Manual Part No.: 8114307 13HENNESSY INDUSTRIE
4 • Important: Always read and follow the information box instructions.When prompted by balance r instructions, use the off-set arm (figure 6A) to
Important: Always read and follow the information box instructions. • 5Figure 7C - T2-Tape (Hidden Tape-A-Weight®) Data EntryDiagramUsing The Laser
6 • Important: Always read and follow the information box instructions.Laser Guided Operation™ SystemThe operator must select T2 - Tape Laser Locator
Important: Always read and follow the information box instructions. • 7Setting Wheel Dimensions (DIM)Before a wheel can be balanced, wheel dimensions
8 • Important: Always read and follow the information box instructions.(See Figure 14A or 14B)1 Weight Display Windows2 Mode Indicators3 Left Weight P
Important: Always read and follow the information box instructions. • 91223456789Figure 14A - 1250 Video Control Panel Feature Reference1223456789Fig
10 • Important: Always read and follow the information box instructions.Control Panel Quick ReferenceScreen Saver Mode (Video)By default, the 1250 vid
Important: Always read and follow the information box instructions. • 11Direct Select™ Weight Placement LocationBefore spinning the wheel, use direct
12 • Important: Always read and follow the information box instructions.Balancing Using Direct Select™A variety of wheel configurations can be balance
Begin by following the Laser Guided Operation™ pro-cedure, steps 1 through 4 on page 6.1. When unbalance is displayed, rotate wheel untilinboard cente
ii • Important: Always read and follow the information box instructions.IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSREAD ALL INSTRUCTIONS1. Ey
14 • Important: Always read and follow the information box instructions.Mounting Wheel on SpindleShaftAvoid back injury, seek assistance when lift-ing
Important: Always read and follow the information box instructions. • 15Standard Front Cone MountingA wheel should be centered by the outer side of t
16 • Important: Always read and follow the information box instructions.Match Balance (Optimization)The Match Balance (Tire/Rim Weight Optimization)pr
Important: Always read and follow the information box instructions. • 17CalibrationMachine CalibrationImportant: Be sure to use the correct calibrati
18 • Important: Always read and follow the information box instructions.3. Bring the tip edge of the arm precisely to the outeredge of the faceplate a
Important: Always read and follow the information box instructions. • 19Diagnostic ProceduresAfter Balance Vibration ProblemsIf vibration is still pr
20 • Important: Always read and follow the information box instructions.Installation InstructionsReceivingThe shipment should be thoroughly inspected
Important: Always read and follow the information box instructions. • 21SpecificationsWheel Diameter Range8 - 30 inchesWheel Width Range2 - 20 inche
8114307 13 6/13 © Copyright 2005 Hennessy Industries and COATS All Rights Reserved Printed in USA
Important: Always read and follow the information box instructions. • iiiOwner’ s ResponsibilityTo maintain machine and user safety, the responsibil-
iv • Important: Always read and follow the information box instructions.Safety Notices and DecalsFailure to follow danger, warning, and cau-tion instr
Important: Always read and follow the information box instructions. • vStandard Safety Devices• STOP key for stopping the wheel under emergencycondit
vi • Important: Always read and follow the information box instructions.Table of ContentsImportant Safety Instructions . . . . . . . . . . . . .iiOwne
Important: Always read and follow the information box instructions. • 1¨Balancing Your First Tire1. Turn the machine OFF then ON(resets machine).Note
2 • Important: Always read and follow the information box instructions.Principle Operating PartsABCDEFGHJKDo It Now!Now is a good time tofill out the
Important: Always read and follow the information box instructions. • 3Know Your UnitCompare this illustration with the unit before placingit into s
Kommentare zu diesen Handbüchern