Coats RC-100 Tire Changer Bedienungsanleitung PDF herunterladen (Seite 12)

8 • Important: Always read and follow operating instructions.

Inflation

On the RC100, tire inflation is performed in two steps:

Bead Seat and Inflation. These steps are explained in

detail on page 10-11. Read the explanation of each step

and understand them thoroughly before proceeding.

CAUTION

Check for proper inflation gauge operation.

Accurate pressure readings are important

to safe tire inflation. Refer to the Operat-

ing Maintenance section of this manual for

instructions.

CAUTION

If the rim has been clamped from the outside

for tire mounting, release the clamps, lift the

tire, and move the clamps to the center of

the table top.

DANGER

Tire failure under pressure is hazardous. This

tire changer is not intended to be a safety

device to contain exploding tires, tubes,

wheels, or bead sealing equipment. Inspect

tire and wheel carefully for match, wear,

or defects before mounting. Always use

approved tire bead lubricant during mount-

ing and inflation.

The inflation pedal, located at the rear of the left side

of the machine, controls the flow of air through the

inflation hose.

NOTE: The clip-on chuck on the end of the hose

should always be an open style with all parts in

proper working order.

Position 1 - At Rest – With the inflation hose attached

to the tire valve and the pedal in this position, the air

gauge will register the air pressure in the tire. Whenever

your foot is removed from the pedal, it will return to this

position.

Position 2 - Tire Inflation – This is the first activated

position. With the inflation hose attached to the tire

valve and the pedal in this position, line pressure is

allowed to flow through the valve and into the tire for

inflation. Tire pressure is not indicated on the gauge in

this position.

Bead Seating

WARNING

Operator should keep hands, arms, and

entire body away from the tire during the

remaining bead seat and inflation proce-

dures. Do not stand over tire, as personal

injury could result.

WARNING

NEVER increase air pressure to exceed 40

PSI when attempting Bead Seat. If operator

is unable to obtain Bead Seat, something is

wrong. Deflate tire completely, inspect both

the tire and wheel, correct any problems

found, relubricate both tire beads, and reat-

tempt Bead Seal and Bead Seat procedures.

Follow all safety instructions in this manual

and on machine.

1. Once tire pressure is indicated on the air gauge

(inflation pedal in position 1; foot removed from pedal),

continue to inject air into the tire in short intervals.

Check the pressure frequently.

Stand back during bead seat. Keep hands, arms, and

entire body away from tire during this procedure.

Tire beads should move outward and “pop” into their

bead seat position as pressure inside the tire increases.

If this does not happen, a problem exists. Investigate

carefully.

WARNING

Check tire pressure frequently. Never exceed

40 PSI while seating beads. Once seated,

never exceed tire manufacturer’s recom-

mended air pressure. Tires can explode,

especially if they are inflated beyond their

limits. At all pressure levels when inflating

through the valve stem, keep hands, arms,

and entire body away from inflating tire.

An exploding tire, wheel, or bead sealing

equipment may propel upward and outward

with sufficient force to cause serious injury

or death to operator or bystander.

Tire Pressure

Tire Inflation

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Coats RC-100 Tire Changer Bedienungsanleitung Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Coats RC-100 Tire Changer