Coats Kit 8114165 Encoder/Sonar Adjustment Bedienungsanleitung PDF herunterladen

XXRR SSeerriieess BBaallaanncceerr EEnnccooddeerr//SSoonnaarr

AAddjjuussttmmeenntt KKiitt 88111144116655

COATS, Inc. • Hennessy Industries • 1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565

(800) 688-6359 • (615) 641-7533 • (615) 641-5104 FAX • www.ammcoats.com

This instruction addresses Errors 55, 57, or 59 that

occur when the value read by the sonar is insufﬁcent

to obtain a correct runout measurement.

1. Make sure the Radial Runout and Lateral Runout

Sonars are aligned correctly.

2. Set Encoder to pulley gap at 0.040”.

3. Go to Self-Test Screen (Green Screen) and verify

that the Encoder is operating correctly and the Sonar is

reading correctly. Use the Sonar check tool (p/n

8114165) or a tape measure and ﬂat card for a target.

XR Model Sonar 4-in Value 14-in Value

Range Range

1800/1850 Width (Hood 2450-2470 8100-8300

mounted, p/n

801800901)

1800/1850 *Radial Runout 3105-3135 8100-8300

(Rear mouted,

p/n 801801331)

1800/1850 Lateral (Front 2450-2470 8100-8300

mounted, p/n

801801261)

1750 Width (Hood 3840-3880 12800-13200

mounted, p/n

801800901)

Closest Target (Sonar) Reading

Farthest Target (Sonar) Reading

4. For XR 1800/1850 software (version 1.06 and

higher) and XR 1750 software (all versions):

From the Green Screen press button 2 for 2 seconds

and then the Encoder Test Screen will appear.

5. With hood down Press START to run the Encoder

Test. It will work with or without a wheel on the

machine. At the end of the Test Run lines of text will

appear below the graphs:

Line 1: > No. ck encoder: ENCA=64 ENCB=64

Both of these values should be 64, if not, an IN or

OUT encoder adjustment (from the 0.040” gap) is indi-

cated.

Line 2:

XR 1800/1850 Models

> Timing signal: ENCA=2000-3500 ENCB=3500-5000

XR 1750 Model

> Timing signal: ENCA=1500-3000 ENCB=2500-4000

(These numbers will vary within the range and some

even outside of the range. The important thing is to get

rid of Line 3: Error reset.)

If the encoder is not set correctly, a third line of text

will appear:

Line 3: > Error reset ENCA or Error reset ENCB

(If one of the above messages appear: Slightly loosen

the small nuts holding the encoder PCB to the bracket.

For ENCA rotate the PCB slightly upward and for ENCB

rotate the PCB slightly downward. Then re-tighten the

small nuts and rerun the Encoder Test.

Rotate the PCB until the Error reset messages are

eliminated.

6. Now, if any Error 55, 57, or 59 appears then the

problem is most likely a very rough tread pattern or

alignment of the sonar. Move the sonar to a different

spot near the center of the tread.

XR 1800/1850 Models 1
XR 1750 Model 1

Inhaltsverzeichnis

Seite 1 - XR 1750 Model

Kommentare zu diesen Handbüchern

Keine Kommentare

Coats Kit 8114165 Encoder/Sonar Adjustment Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Coats Kit 8114165 Encoder/Sonar Adjustment herunter. COATS Kit 8114165 Encoder/Sonar Adjustment User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Coats Kit 8114165 Encoder/Sonar Adjustment