1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 Manual Part No.: 8184121 01HENNESSY INDUSTRIES INC. Manufactur
3. Tighten the locking handle and move the tool intoposition near the edge of the rim, as shown above.4. Insert the bead lifting tool between the rim
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 5Bead Loosening and Demounting1. After chucking the wheel, position the beadloosener disc against the sidew
Bead Loosening1. Remove the valve core. Deflate the tire away fromthe machine and remove any calcium chloride or othersubstances from the tire prior t
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 73. Rotate the wheel counterclockwise while main-taining pressure on the spade tool until the outer beadis
Demounting1. By operating the carriage to the extended posi-tion, the table will be rotated to the horizontal position.2. Place the tire and rim over
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 911. Using table cylinder, press tire and inner tiredown off of rim.12. Remove compressor and rim from tabl
Mounting1. Place the two inner tire side plates into the car-riage forward holes facing each other as shown above.2. Place the shortest nylon web stra
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 119. Place the combo tool "tee" into the carriage withthe "tee" perpendicular to the ca
21. Remove compressor and retaining ring.22. Place rim seal down around rim and under bead.23. Place retaining ring, and lock ring, on top of tire.24.
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 13Extended Service Kit ItemsHennessy Model 8090011 (GM 10603931) - H.I.T.5000H2 Tire changer with extended
ii • COATS H.I.T. 5000H2 ChangerSafety
6. Remove the pressure sensor tubing. Remove thewheel nuts.7. Extend the ram to full length, install the yokeextension, and tire compressor making sur
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 1514. Lower the wheel to the point where the rollerassembly can be moved forward without catching onthe rim
Mounting1. Re-clamp a new tire onto the jaws of the tirechanger.2. Place the two bead spreaders into the lower edgeof the bead with the other end hook
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 1710. Move the carriage back out allowing the insertto drop fully into the tire. Note:This may require adju
23. Extend the carriage, moving the end plate into avertical position.24. Stand the wheel upright and walk it into place,against the end plate, with t
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 19There are two methods of spreading the tire with theroller tool.Method A:1. With the first bead removed,
H.I.T. 5000H220 • COATS H.I.T. 5000H2 Changer1. Using a grease gun and chassis grease, lubricatechuck hub bushing once every month.2. Remove the side
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 21Notes
8184121 10/09 © Copyright 2000 Hennessy Industries and COATS All Rights Reserved Printed in USATruck Tire Changer Warranty PolicyThe COATS Company war
COATS H.I.T. 5000H2 Changer • iiiTable of ContentsOperator Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv • COATS H.I.T. 5000H2 ChangerSafetyFailure to follow danger, warning, and cautioninstructions may lead to serious personal injury ordeath to operat
COATS H.I.T. 5000H2 Changer • vSafety InstructionsOnly properly trained personnel shouldservice tires on the H.I.T. 5000H2. Read allsafety and operati
vi • COATS H.I.T. 5000H2 ChangerH.I.T. 5000H2InstallationIt is not necessary to bolt the H.I.T. 5000H2 to thefloor. However, if desired, use the holes
COATS H.I.T. 5000H2 Changer • 1Principal Operating PartsSpecificationsWorking Area: 10 Foot Wide x 12 Foot Long x 8 Foot HeightWeight: 1,600 PoundsHan
Wheel ClampingThe self-centering chuck is powered by the high pres-sure hydraulic system to securely lock onto the wheel.Important: The hydraulic pres
H.I.T. 5000H2COATS H.I.T. 5000H2 Changer • 3Bead Loosening1. After locking the wheel on the chuck, remove thevalve core and deflate the tire completel
Kommentare zu diesen Handbüchern