Coats 16 Bit PCB & Metal Arm Temporary Bedienungsanleitung PDF herunterladen

8113936 00 10/04 page 1 of 4

16 Bit PCB & Metal Arm Temporary

Instructions - 1800/1850 Balancer

COATS, Inc. • Hennessy Industries • 1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565

(800) 688-6359 • (615) 641-7533 • (615) 641-5104 FAX • www.ammcoats.com

Instructions

1. The Plastic Diameter Arm on the end of the dis-

tance rod has been replaced with a more robust Metal

Diameter Arm. The plastic roller step is placed under

the bead seat area of the rim for all normal measure-

ments (clip-on weights and Rim Runout) and the large

diameter is placed at the point of application for tape-a-

weights.

2. On startup, the software recognizes whether the

machine is 1800 or 1850 and the appropriate menus

appear.

3. Important: It is necessary to perform a NOVRAM

reset on startup.

4. Power up machine and check for function of all

operations. Make any necessary adjustments:

• Ensure that Distance and Diameter Pots are set

between 2500 & 3500 on Machine Self-Test (Green

Screen).

• If Arm Calibrations are required:

Press the key and select the SERVICE

ADJUSTMENTS option . At the PASSWORD

prompt enter 1-3-5-7.

Toggle the DISTANCE/DIAMETER ARM TYPE

option to METAL.

In the following order, select the DISTANCE ARM

CALIBRATION option , WIDTH SONAR CALI-

BRATION option , and DIAMETER ARM CALI-

BRATION option

following the on-screen

instructions for each calibration. Note: At the end of

the Diameter Arm Calibration, hold the NEXT but-

ton down until 281 degrees ﬂashes on-screen; then

return the arm to its home position.

Important: Once the Arm is calibrated, there is lit-

tle need to calibrate it again.

5. If the machine is an 1850 model or upgrade, a

Printer selection will appear in the GENERAL SETUP

menu (press the key, then select option ). At

the PRINTER menu select option to verify that the

printer option is toggled ON. For all other options the

default is ON.

An LED on the face of the printer will blink every sec-

ond to verify that the printer is powered.

6. To Calibrate with the 4-ounce weight, press the

key, then select SPECIAL FUNCTIONS option

and choose MACHINE SELF-CALIBRATION selec-

tion

Follow the instructions on-screen.

Important: The dimensions entered must match the

“calibration wheel”. A dimension cannot be zero.

7. If not already done, you may want to enter the

Owner Name and Address for the screen saver. The

OWNER ADDRESS selection is found under the SPE-

CIAL FUNCTIONS menu.

8. The Board is factory set with the following menu

settings:

General Set-up

Printer = ON

Runout Unloaded " = SONAR (lateral)

Runout Unloaded # = SONAR (radial)

alancing Set-up

Runout Diagnostic = ON

Runout Limits

Max. True Limit = .050"

Rim Runout Limit = .010"

Correction Runout Limit = .030"

Special Functions

Static Unbalance Displayed = ON

Stop On Top = OFF

9. Refer to ﬁgure 1 showing the proper placement of

the metal arm roller on the rim.

Figure 1 - Placing The Metal Arm Roller On The Rim

10. See the new error code listing on the following

pages.

1 2 3 4

Instructions 1

Inhaltsverzeichnis

Seite 1 - Instructions

8113936 00 10/04 page 1 of 416 Bit PCB & Metal Arm TemporaryInstructions - 1800/1850 BalancerCOATS, Inc. • Hennessy Industries • 1601 J.P. Henne

Seite 2

ErrorNoVideoErr. 1Err. 2Err. 3Err. 4Err. 5Err. 6Err. 7 /Err. 8Err. 9SymptomThe balancer does not turn on.Rotation signal missing.Wheel spins too fast

Seite 3

ErrorErr. 11Err. 12Err.13Err.14Err.17Err.18Err.15 /Err.16 / Err.19Err.20Err. 21Err. 22Err. 23Err. 25Err. 30Err.40,4142, 43Err.45,46, 47,48Err.50,51, 5

Seite 4

ErrorErr.54Err.55Err.56Err.57Err.58Err 59Err.65SymptomError in the Sonar reading.Sonar did not read any value.Error in the Radial Sonar reading.The va

Kommentare zu diesen Handbüchern

Keine Kommentare

Coats 16 Bit PCB & Metal Arm Temporary Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Coats 16 Bit PCB & Metal Arm Temporary herunter. COATS 16 Bit PCB & Metal Arm Temporary User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Coats 16 Bit PCB & Metal Arm Temporary